M: TRex 250SE regu RCEBL15X & Turnigy AE-20A 2ABEC 2-4S
Posted: Fri Jul 30, 2010 19:17
Ehk siis tutikad regulaatorid harjadeta (brushless) mootoritele:
1) KX880003A Align 15A Brushless ESC (Governer Mode) ehk siis Align RCE-BL15X (DC 5,5V-12,6V; 15A) = 600 eek
Specification:
-Continuous current:15Amps with porper air flow
-Surge current:20Amps
-Supporting motor types:2 poles to 10+poles in/outrunner brushless motors
-Supporting maximum RPM:2poles=>190,000rpm
-Supporting input voltage:5.5V~12.6V
-BEC output voltage: 5-6V step-less adjustment
-Supporting battery types: Li-Po 2~3 cells
-Size:42X24X9.3mm
-Weight:15g
2) Turnigy AE-20A 2ABEC 2-4S LI-PO = 250 eek
The Turnigy AE series are based on new powerful microprocessor.
The new CPU means ultra fast sync timing, crisper throttle response, less battery load and reduced FET heat buildup. Also there is a separate voltage regulator IC for microprocessor providing good anti-jamming capability.
Specification:
Output: Continuous 20A, burst 25A up to 10 seconds.
Input Voltage: 2-4 cells lithium battery or 5-12 cells NIMH battery.
BEC: Linear 2A @ 5V
Control Signal Transmission: Optically coupled system.
Max Speed:
2 Pole: 210,000rpm
6 Pole: 70,000rpm
12 Pole: 35,000rpm
Size: 50mm (L) * 26mm (W) * 12mm (H).
Weight: 19g.
Features:
High performance microprocessor brings out the best compatibility with all kinds of motors and the highest driving efficiency.
Wide-open heatsink design to get the best heat dissipation effect.
Improved Normal, Soft, Very-Soft start modes, compatible with aircraft and helicopter.
Smooth, linear, quick and precise throttle response.
Multiple protection features: Low-voltage cut-off protection / Over-heat protection / Throttle signal loss protection
Programable via transmitter and Turnigy BESC programming card
Programming features:
Brake setting (we recommend using brake for only folding props applications)
Battery type(Li-xx or Ni-xx)
Low voltage cutoff setting
Factory default setup restore
Timing settings (to enhance ESC efficiency and smoothness)
Soft acceleration start ups (for delicate gearbox applications)
Low voltage cutoff type (power reduction orirnmediate shutdown)
Factory default settings:
Brake: off
Battery type: Li-xx (Li-ion or Li-Po)
Low voltage cutoff threshold: Soft cut-off (2.6V)
Timing setup: Low
Soft Acceleration Start Up: Normal
Low voltage cutoff type: Medium
----
Kontakt: foorumi PM või sms 51-12172
I.
1) KX880003A Align 15A Brushless ESC (Governer Mode) ehk siis Align RCE-BL15X (DC 5,5V-12,6V; 15A) = 600 eek
Specification:
-Continuous current:15Amps with porper air flow
-Surge current:20Amps
-Supporting motor types:2 poles to 10+poles in/outrunner brushless motors
-Supporting maximum RPM:2poles=>190,000rpm
-Supporting input voltage:5.5V~12.6V
-BEC output voltage: 5-6V step-less adjustment
-Supporting battery types: Li-Po 2~3 cells
-Size:42X24X9.3mm
-Weight:15g
2) Turnigy AE-20A 2ABEC 2-4S LI-PO = 250 eek
The Turnigy AE series are based on new powerful microprocessor.
The new CPU means ultra fast sync timing, crisper throttle response, less battery load and reduced FET heat buildup. Also there is a separate voltage regulator IC for microprocessor providing good anti-jamming capability.
Specification:
Output: Continuous 20A, burst 25A up to 10 seconds.
Input Voltage: 2-4 cells lithium battery or 5-12 cells NIMH battery.
BEC: Linear 2A @ 5V
Control Signal Transmission: Optically coupled system.
Max Speed:
2 Pole: 210,000rpm
6 Pole: 70,000rpm
12 Pole: 35,000rpm
Size: 50mm (L) * 26mm (W) * 12mm (H).
Weight: 19g.
Features:
High performance microprocessor brings out the best compatibility with all kinds of motors and the highest driving efficiency.
Wide-open heatsink design to get the best heat dissipation effect.
Improved Normal, Soft, Very-Soft start modes, compatible with aircraft and helicopter.
Smooth, linear, quick and precise throttle response.
Multiple protection features: Low-voltage cut-off protection / Over-heat protection / Throttle signal loss protection
Programable via transmitter and Turnigy BESC programming card
Programming features:
Brake setting (we recommend using brake for only folding props applications)
Battery type(Li-xx or Ni-xx)
Low voltage cutoff setting
Factory default setup restore
Timing settings (to enhance ESC efficiency and smoothness)
Soft acceleration start ups (for delicate gearbox applications)
Low voltage cutoff type (power reduction orirnmediate shutdown)
Factory default settings:
Brake: off
Battery type: Li-xx (Li-ion or Li-Po)
Low voltage cutoff threshold: Soft cut-off (2.6V)
Timing setup: Low
Soft Acceleration Start Up: Normal
Low voltage cutoff type: Medium
----
Kontakt: foorumi PM või sms 51-12172
I.